Subaru Outback (BR): General Description (Diagnostic Trouble Code (DTC) )
Subaru Outback (BR) 2010-2015 Service Manual / Engine - H4SO / General Description (Diagnostic Trouble Code (DTC) )
List of Diagnostic Trouble Code (DTC)
A: LIST
- DTC P0026, P0028, P0030, P0031, P0032, P0037, P0038, P0068, P0076, P0077, P0082, P0083, P0101, P0102, P0103
- DTC P0107, P0108, P0111, P0112, P0113, P0117, P0118, P0122, P0123, P0125, P0126, P0128
- DTC P0131, P0132, P0133, P0134, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P014C, P014D, P015A, P015B
- DTC P0171, P0172, P0181, P0182, P0183, P0196, P0197, P0198, P0201, P0202, P0203, P0204, P0222, P0223, P0301, P0302, P0303, P0304
- DTC P0327, P0328, P0335, P0336, P0340, P0341, P0351, P0352, P0353, P0354, P0400, P0420
- DTC P0442, P0447, P0448, P0451, P0452, P0453, P0456, P0457, P0458, P0459, P0461, P0462, P0463, P0464
- DTC P0500, P0506, P0507, P050A, P050B, P0512, P0513, P0604, P0605, P0607, P0638, P0700, P0851, P0852
- DTC P1152, P1153, P1160, P1443, P1492, P1493, P1494, P1495, P1496, P1497, P1498, P1499, P1518, P1560, P1570, P1571, P1572, P1574, P1576, P1577, P1578
- DTC P2096, P2097, P2101, P2102, P2103, P2109, P2122, P2123, P2127, P2128, P2135, P2138, P2227, P2228, P2229, P2610
- DTC U0073, U0101, U0122, U0140, U0402, U0416, U0422
READ NEXT:
DTC P0026, P0028, P0030, P0031, P0032, P0037, P0038, P0068, P0076, P0077,
P0082, P0083, P0101, P0102, P0103
A: DTC P0026 INTAKE VALVE CONTROL SOLENOID CIRCUIT RANGE/PERFORMANCE
(BANK 1)
1. OUTLINE OF DIAGNOSIS
Judge as NG with either Low NG or High NG.
A variable valve lift diagnosis oil pressure switch is
DTC P0107, P0108, P0111, P0112, P0113, P0117, P0118, P0122, P0123, P0125,
P0126, P0128
P: DTC P0107 MANIFOLD ABSOLUTE PRESSURE/BAROMETRIC PRESSURE
CIRCUIT LOW INPUT
1. OUTLINE OF DIAGNOSIS
Detect the open or short circuit of intake manifold pressure sensor.
Judge as NG if out of specif
DTC P0131, P0132, P0133, P0134, P0137, P0138, P013A, P013B, P013E, P013F,
P0140, P0141, P014C, P014D, P015A, P015B
AB:DTC P0131 O2 SENSOR CIRCUIT LOW VOLTAGE (BANK 1 SENSOR 1)
1. OUTLINE OF DIAGNOSIS
Detect the open or short circuit of sensor.
Judge as NG, when the element voltage is out of the specified range.
2
SEE MORE:
Airbag Connector, Diagnostic Trouble Code
A: PROCEDURE
For operation procedures, refer to "Airbag Connector" of Airbag System. <Ref. to AB-18, Airbag Connector.>
Airbag Control Module I/O Signal
A: ELECTRICAL SPECIFICATION
Type A
Terminal numbers in airbag control module connector are shown in the fig
High/low beam change (dimmer)
To change from low beam to high beam, push the turn signal lever forward. When
the headlights are on high beam, the high beam indicator light “”
on the combination meter is also on.
To switch back to low beam, pull the lever back to the detent position.
© 2010-2025 Copyright www.suoutback.com
