Subaru Outback manuals

Subaru Outback: Oil Pump Cover

A: REMOVAL

1) Remove the transmission assembly from the vehicle.

<Ref. to 5AT-37, REMOVAL, Automatic Transmission Assembly.>

2) Pull out the torque converter assembly. <Ref. to 5AT-63, REMOVAL, Torque Converter Assembly.>

3) Remove the transmission harness connector from stay.

4) Remove the ATF cooler inlet pipe and outlet pipe. <Ref. to 5AT-58, REMOVAL, ATF Cooler Pipe and Hose.>

5) Separate the converter case and transmission case. <Ref. to 5AT-78, REMOVAL, Converter Case.>

6) Remove the oil pump cover mounting bolt, and then separate the oil pump cover from the AT main case by lightly tapping with plastic hammer.

Subaru Outback. Automatic Transmission

B: INSTALLATION

1) Secure the oil pump cover.

NOTE: Use a new gasket.

Tightening torque: 41 N*m (4.2 kgf-m, 30.2 ft-lb)

Subaru Outback. Automatic Transmission

2) Install the converter case assembly to the transmission case assembly. <Ref. to 5AT-63, INSTALLATION, Torque Converter Assembly.>

3) Install the transmission harness connector to the stay.

4) Install the ATF cooler pipe. <Ref. to 5AT-59, INSTALLATION, ATF Cooler Pipe and Hose.>

5) Install the torque converter assembly. <Ref. to 5AT-63, INSTALLATION, Torque Converter Assembly.>

6) Install the transmission assembly to the vehicle.

<Ref. to 5AT-42, INSTALLATION, Automatic Transmission Assembly.>

C: DISASSEMBLY

1. FRONT BRAKE

1) Remove the snap ring.

Subaru Outback. Automatic Transmission

2) Remove the retaining plate, drive plate and driven plate.

3) Using the ST1, ST2 and ST3, remove the snap ring.

ST1 18762AA000 COMPRESSOR SPECIAL TOOL
ST2 18765AA000 COMPRESSOR SUPPORT
ST3 18763AA000 COMPRESSOR SHAFT

Subaru Outback. Automatic Transmission

4) Remove the retainer and return spring.

5) Remove the front brake piston using compressed air.

Subaru Outback. Automatic Transmission

6) Remove the D-ring from front brake piston.

2. OIL PUMP

1) Take out the oil pump housing.

Subaru Outback. Automatic Transmission

2) Take out the oil pump body.

D: ASSEMBLY

1. FRONT BRAKE

1) Apply ATF to D-ring, and then install it to the front brake piston.

NOTE: Use a new D-ring.

2) Install the front brake piston to oil pump cover.

NOTE: Install by aligning the "Subaru Outback. Automatic Transmission" mark on front brake piston surface with the oil pump cover rib.

Subaru Outback. Automatic Transmission

3) Install the retainer and return spring.

4) Install the front brake piston assembly using ST1, ST2 and ST3.

ST1 18762AA000 COMPRESSOR SPECIAL TOOL
ST2 18765AA000 COMPRESSOR SUPPORT
ST3 18763AA000 COMPRESSOR SHAFT

Subaru Outback. Automatic Transmission

5) Install the genuine driven plate instead of retaining plate, and temporarily assemble the drive plate and driven plate.

Part No. 31536AA290 Driven plate 6) Install the snap ring.

Subaru Outback. Automatic Transmission

7) Measure the clearance between the retaining plate and snap ring. If the value exceeds the specification, replace the drive plate and driven plate as a set and select the retaining plate so that the value is within the specification.

NOTE: The thickness of the genuine drive plate is 2.8+-0.05 mm (0.11+-0.002 in).

Front brake clearance specification: 0.7 - 1.1 mm (0.028 - 0.043 in)

Subaru Outback. Automatic Transmission

8) Remove the snap ring, replace the driven plate used in measurement of clearance with the retaining plate, and then reassemble.

2. OIL PUMP

1) Apply ATF to oil pump assembly, and then install it to oil pump housing.

2) Install the O-ring to oil pump cover.

NOTE: Use new O-rings.

3) Install the oil pump housing to the oil pump cover.

Tightening torque: 10 N*m (1.0 kgf-m, 7.4 ft-lb)

Subaru Outback. Automatic Transmission

E: INSPECTION

1. FRONT BRAKE

Check the following items.

2. OIL PUMP

Check the following items.

1) Check the seal ring and oil seal for breaks and damage.

2) Check other parts for dents or faults.

3) Oil pump rotor assembly selection

  1. Tip clearance
    Install the inner rotor and outer rotor to oil pump housing. With rotor gears facing each other, measure the crest-to-crest clearance.

Tip clearance: 0.02 - 0.15 mm (0.0008 - 0.0059 in)

Subaru Outback. Automatic Transmission

  1. Thickness gauge
  2. Inner rotor
  3. Outer rotor
  1. Side clearance
    Set a depth gauge to oil pump housing, then measure the oil pump housing-to-rotor clearance.

Side clearance: 0.02 - 0.045 mm (0.0008 - 0.0018 in)

Subaru Outback. Automatic Transmission

  1. Depth gauge
  2. Inner rotor
  3. Outer rotor
  1. If the tip and/or side clearance are not within the specification, replace the rotor assembly.

Subaru Outback. Automatic Transmission

Check the total end play and adjust it to be within specifications. <Ref. to 5AT-103, ADJUSTMENT, AT Main Case.>

READ NEXT:

 Drive Pinion Shaft Assembly

A: REMOVAL 1) Remove the transmission assembly from the vehicle. <Ref. to 5AT-37, REMOVAL, Automatic Transmission Assembly.> 2) Pull out the torque converter assembly. <Ref. to 5AT-63, REMO

 AT Main Case

A: REMOVAL 1) Remove the transmission assembly from the vehicle. <Ref. to 5AT-37, REMOVAL, Automatic Transmission Assembly.> 2) Pull out the torque converter assembly. <Ref. to 5AT-63, REMO

 Transmission Control Device

A: REMOVAL 1) Remove the transmission assembly from the vehicle. <Ref. to 5AT-37, REMOVAL, Automatic Transmission Assembly.> 2) Pull out the torque converter assembly. <Ref. to 5AT-63, REMO

SEE MORE:

 Oil pressure warning light

CAUTION Do not operate the engine with the oil pressure warning light on. This may cause serious engine damage. If this light illuminates when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system is not working properly. If the light illumina

 General Description

A: COMPONENT Front sub sensor RH Front sub sensor LH Airbag warning light (in combination meter) Airbag module ASSY (driver) Airbag module ASSY (passenger) Airbag control module Steering roll connector Curtain airbag sensor LH Curtain airbag module LH Front door impact sensor LH Cur

© 2010-2022 Copyright www.suoutback.com