Subaru Outback (BR): General Description of Trim
A: COMPONENT
1. FRONT UNDER COVER
- Small type
- Medium type
- Large type
Tightening torque: N*m (kgf-m, ft-lb)
T: 17.5 (1.78, 12.9)
2. FLOOR UNDER PROTECTOR
Tightening torque: N*m (kgf-m, ft-lb)
T: 7.5 (0.76, 5.5)
3. FUEL TANK PROTECTOR
- Fuel tank protector RH
- Fuel tank band ASSY RH
- Fuel tank ASSY
- Fuel tank band ASSY LH
- Center heat shield cover (DOHC model)
- Fuel tank bracket
- Fuel tank protector LH
- Center heat shield cover (SOHC model)
Tightening torque: N*m (kgf-m, ft-lb)
T1: 9 (0.92, 6.6)
T2: 18 (1.84, 13.3)
T3: 33 (3.36, 24.3)
4. FRONT HOOD GRILLE
- Front hood grille
- Clip anchor
- Bolt
- Protector
- Gasket
- Grommet
- Hood duct
- Hood duct inner
- Clip
Tightening torque: N*m (kgf-m, ft-lb)
T1: 1.0 (0.1, 0.7)
T2: 4.5 (0.46, 3.3)
5. FRONT BUMPER
- Floor ornament
- Front grille ASSY
- Grille bracket
- Front bumper face
- Front hook cover
- Bumper cover CTR (sedan model only)
- Bumper cover (OUTBACK model)
- Fog light cover (OUTBACK model)
- Bumper cover (sedan model)
- Fog light cover (sedan model)
- Bracket corner front
- Bracket side front UPR
- Bracket center LWR front
- Energy absorber foam front
- Beam COMPL front
Tightening torque: N*m (kgf-m, ft-lb)
T1: 7.5 (0.76, 5.5)
T2: 32 (3.26, 23.6)
6. REAR BUMPER
- Beam COMPL rear
- Energy absorber foam rear
- Bracket side rear UPR
- Bracket corner rear
- Bracket side rear LWR
- Rear hook cover
- Bumper cover rear
- Rear bumper face
Tightening torque: N*m (kgf-m, ft-lb)
T1: 7.5 (0.76, 5.5)
T2: 45 (4.59, 33.2)
- Beam COMPL rear
- Energy absorber foam rear
- Bracket side rear UPR
- Bracket corner rear
- Bracket side rear LWR
- Reflex reflector
- Rear hook cover
- Rear bumper face
Tightening torque: N*m (kgf-m, ft-lb)
T1: 7.5 (0.76, 5.5)
T2: 45 (4.59, 33.2)
7. MUD GUARD
- Front mud guard
- Front air flap plate
- Fender cover lower
- Rear air flap plate
- Rear mud guard
8. COWL PANEL
- Cowl panel side LH
- Cowl panel
- Cowl panel side RH
- Washer hose
- Washer nozzle
- Cowl panel seal
9. SIDE SILL SPOILER
- Side sill garnish ASSY (sedan model)
- Garnish ASSY front fender (OUTBACK model)
- Garnish ASSY front door (OUTBACK model)
- Garnish ASSY rear door (OUTBACK model)
- Garnish ASSY rear quarter (OUTBACK model)
- Side sill garnish ASSY (OUTBACK model)
10.ROOF MOLDING
- Rivet
- Roof molding
- Clip
11.ROOF RAIL
- Roof molding
- Roof rail ASSY
- Rivet
- Clip
Tightening torque: N*m (kgf-m, ft-lb)
T: 7.5 (0.76, 5.5)
12.TRUNK LID GARNISH
- Trunk lid garnish
- Undercover-trunk lid garnish
13.REAR GATE GARNISH
- License light ASSY and rear gate opener ASSY harness.
- Rear gate garnish
- Ornament
- Garnish LWR
Tightening torque: N*m (kgf-m, ft-lb)
T: 4.5 (0.46, 3.3)
14.DOOR TRIM
- Gusset cover front
- Inner remote ASSY
- Weather strip inner
- Front door inner remote cover
- Front door trim ASSY
- Door step light
- Front door ornament panel
- Power window switch panel front RH
- Door lock switch ASSY
- Power window sub-switch ASSY front
- Power window switch panel front LH
- Power window main switch ASSY
- Rear door inner remote cover
- Rear door trim
- Rear door cover upper
- Power window switch panel rear
- Power window sub-switch ASSY rear
- Rear door ornament panel
15.CONSOLE BOX
- Console lid COMPL
- Console lid hinge COMPL
- Lid lock UPR
- Lid inner UPR
- Console front side cover ASSY RH
- Console front side cover ASSY LH
- Mat (lid LWR)
- Lid inner LWR
- Lid outer LWR
- Lid lock LWR
- Console box LWR RH
- Console box LWR LH
- Pocket case
- Cover center
- Mat (pocket)
- Console pocket
- Console rear cover
- Console bracket
- Cover A
- Accessory socket
- Cover B
- AUX unit
Tightening torque: N*m (kgf-m, ft-lb)
T: 6.5 (0.66, 4.8)
- Center pocket mat
- Front cover AT
- Front cover MT
- Indicator ASSY AT
- Shift boot (MT model)
- Switch case
- Seat heater switch
- Cup holder ASSY
16.INSTRUMENT PANEL
- Instrument panel ASSY
- Switch panel ASSY
- Ornament panel ASSY D OUT
- Fuse lid
- Instrument panel lower cover
- Instrument panel lower cover under
- Trunk opener cancel button
- Ornament panel ASSY P
- Glove box lid ASSY
- Key cylinder - glove box
- Illumination LED ASSY
- Illumination bracket
- Glove box back panel
- Glove box under cover
- Glove box damper
- Instrument panel side cover
- Instrument panel pad and frame ASSY
- Navigation bracket
- Navigation ASSY
- Audio bracket
- Audio ASSY
- Center grille ASSY LH
- Center grille ASSY RH
- Center panel ASSY
- Center cover side RH
- Insulator
- Pocket center light
- Pocket ASSY (without lid)
- Pocket ASSY (with lid)
- Center pocket mat
- Control panel ASSY
- Plug
- Accessory socket ASSY
- Center pocket back panel
- Center cover side LH
- Multi display panel UPR
- Multi display ASSY
- Center speaker cover
- Multi display panel LWR
- Side speaker cover
- Front side speaker ASSY
- Defroster side grille RH
- Side vent grille ASSY RH
- Meter reinforcement panel
- Meter visor ASSY
- Combination meter ASSY
- Steering upper cover
- Starter switch cover
- Ornament panel ASSY D INN
- Side vent grille ASSY LH
- Defroster side grille LH
- Sunload sensor
- TORX bolt
- Adjuster bolt
- Passenger's airbag module ASSY
- Steering support beam ASSY
- Knee guard panel COMPL
- Instrument panel pad and frame ASSY
Tightening torque: N*m (kgf-m, ft-lb)
T1: 7.5 (0.76, 5.5)
T2: 3 (0.31, 2.2)
T3: 18 (1.84, 13.3)
T4: 25 (2.55, 18.4)
- Insulator
- Front defroster nozzle ASSY
- Side defroster duct RH
- Instrument panel pad and frame ASSY
- Side vent duct LH
- Center vent duct
- Side vent duct RH
- Side defroster duct LH
17.INNER TRIM
- Front pillar trim
- Side sill cover front
- Side sill cover-front OUT
- Side sill cover-front INN
- Center pillar trim UPR
- Center pillar trim LWR
- Side sill cover-rear OUT
- Catcher cover
- Side sill cover-rear INN
- Rear quarter trim LWR
- Rear quarter trim UPR
- Child anchor cap
- High-mounted stop light ASSY
- Rear shelf panel
- Trunk lid trim
- Trunk trim panel ASSY-front LH
- Trunk trim panel ASSY-front RH
- Trunk trim panel ASSY-side
- Trunk trim panel ASSY-rear
- Trunk mat
- Front pillar trim
- Side sill cover front
- Side sill cover-front OUT
- Side sill cover-front INN
- Center pillar trim UPR
- Center pillar trim LWR
- Side sill cover-rear OUT
- Catcher cover
- Side sill cover-rear INN
- Rear quarter trim UPR-front
- Rear quarter trim UPR-rear
- Hook
- Rear quarter trim LWR
- Rear floor mat RH
- Rear floor spacer RH
- Rear floor mat CTR
- Rear floor edge cover
- Rear floor mat LH
- Rear floor spacer LH
- Rear floor spacer CTR-front
Tightening torque: N*m (kgf-m, ft-lb)
T: 7.5 (0.76, 5.5)
18.REAR GATE TRIM
- Rear gate pillar trim RH
- Rear gate upper trim
- Rear gate pillar trim LH
- Rear gate lower cap LH
- Rear gate lower trim
- Rear gate lower cap RH
- Rear gate handle
19.ROOF TRIM
- Model with sunroof
- Normal roof model
- Sun roof garnish
- Roof cord ASSY
- Roof trim
- Feeder cord ASSY
- Seat belt holder cover
- Seat belt holder base
- Speaker cover
- Child anchor cover
20.ROOM INNER PARTS
- Room mirror
- Sun visor
- Assist grip bracket
- Assist grip
Tightening torque: N*m (kgf-m, ft-lb)
T: 7.5 (0.76, 5.5)
21.HEAT SHIELD COVER
- Front heat shield cover
- Center heat shield cover (DOHC model)
- Center heat shield cover (SOHC model)
- Rear heat shield cover RH (only DOHC model)
- Rear heat shield cover LH
Tightening torque: N*m (kgf-m, ft-lb)
T1: 10 (1.02, 7.4)
T2: 18 (1.84, 13.3)
B: PREPARATION TOOL
READ NEXT:
A: REMOVAL
1) Remove the front bumper face assembly.
Remove the clips, turn over the front mud guard, and disconnect the fog
light connector. (Model with
fog light)
Remove the clips at the up
A: REMOVAL
1) Open the front hood.
2) Remove the front wiper arm assembly.
CAUTION:
Follow the steps below when standing up the wiper arm. Not following the steps
may cause contacting
of wiper arms
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the front bumper face assembly.
Remove the clips, turn over the front mud guard, and disconnect the fog
light connector. (Model w
SEE MORE:
It is necessary to pull off the fender lining when replacing some bulbs.
1. Start the engine and turn the steering wheel fully in the opposite direction
of the bulb to be replaced.
2. Stop the engine.
3. Remove the clip from the fender lining. Refer to “Type B clips” F11-5.
4. Pull off
When in the SAT mode, press the “SEEK” button “”
or “” continuously to change to the
channel selection mode. Pressing the “SEEK” button “”
changes the channel up by 10 steps each time. Pressing “”
changes the channel down by 10 steps each time.
© 2010-2024 Copyright www.suoutback.com